Technical Sharing
2026/11/20
When Does a Linear Transport System Become the Best Choice for High Mix Manufacturing?
20
2026/11/
Product variety alone does not justify a new transport platform. A factory running several variants through identical operations may perform well with conventional conveying. The challenge changes when those variants need different processing times, workstation visits, or carrier arrangements. Transport then becomes part of production coordination, influencing how easily the line can accommodate its changing workload.
An intelligent conveyor system becomes a stronger candidate when independent product movement addresses those differences economically. We begin by examining the production mix and its effect on flow, rather than assuming that faster transfer will make a mixed-product line more productive.

The Tipping Point Is a Shared Motion Pattern That No Longer Fits
Consider two product variants using the same assembly area. Both require loading and inspection, but one needs an additional processing step. If every carrier advances together, the simpler product may spend time waiting for an operation it does not need. Different dwell times can create similar restrictions.
Independent movers offer another approach. Our Flexible Transport System at FHS uses electromagnetic force to drive magnet-equipped movers individually along a guide rail. Its published architecture combines magnetic drive modules, intelligent control, and configurable tracks, providing building blocks for application-specific movement.
However, independent control does not automatically allow products to overtake one another. A mover waiting on a shared track can still affect those behind it. Passing, alternative routes, parallel stations, or buffers require suitable physical arrangements. We evaluate scheduling and track topology together because software cannot create space that the layout lacks.
The strongest opportunity therefore appears when independent movement can remove a demonstrated flow restriction. If every product follows the same sequence at the same pace, the additional control capability may offer less value. The comparison should focus on accepted output and operating cost across the intended mix.
A Linear Transport System Must Match the Mix Physically
Motion flexibility is useful only when the products and fixtures remain mechanically compatible. Manufacturers need to define combined payload, center of gravity, fixture dimensions, process forces, and movement limits. A lightweight product on a large fixture can require more spacing than a heavier product carried in compact tooling.
Our FTS-MT basic parameter table lists a typical load of up to 40 kg, repetitive positioning accuracy of ±0.01 mm, and modular expansion support. The product highlights also describe replaceable movers and tooling and customizable workstations. These specifications provide screening information before detailed application assessment.
For mixed production, we also examine the interface between carrier and workstation. Different variants may share transport hardware while requiring dedicated nests, clamps, or tools. Where fixtures change, teams should establish how their identity is verified and how incorrect combinations are prevented before processing begins.
An intelligent conveyor system cannot eliminate product-specific tooling requirements. Its advantage may instead be retaining a common transport platform while modifying selected fixtures and stations. That distinction matters when estimating how much engineering and downtime the next product introduction will require.
Scheduling Becomes a Production Resource
Once movement is independently controlled, workstation allocation becomes important. The control concept must explain which product receives the next available station, how queues are limited, and what happens when a process takes longer than expected. Poor scheduling can leave capable equipment underused or create unnecessary congestion.
Our iFCS control software documents individual mover control, configurable workstation scheduling, dynamic grouping, and external workstation synchronization. It uses a standard PLCopen interface and supports user-driven secondary development. These functions are relevant when translating a mixed-product process plan into coordinated equipment behavior.
Product identification requires another distinction. Recognizing a mover establishes its transport identity; knowing the product variant, completed operations, and inspection status requires the appropriate data association. At FHS, we recommend defining that association explicitly when discussing the production application.
Rejected products also affect scheduling. Our transport documentation describes moving detected defective products directly to an unloading station. Whether that action avoids unnecessary processing depends on the configured route and rejection location. Buyers should verify the complete sequence, including inspection signals and confirmation that the correct unit was removed.
Test the Difficult Mix Before Committing to the Layout
A useful evaluation of a linear transport system includes more than a nominal production recipe. We recommend testing an uneven mix, a sudden increase in the slowest variant, replenishment delays, and workstation interruptions. These conditions reveal whether the proposed arrangement remains workable as demand changes.
Simulation provides a practical way to investigate those scenarios before installation. Our iFTS Studio supports graphical track configuration for straight, loop, and diverging topologies, alongside system simulation. Model inputs still need realistic processing times, loading patterns, and recovery assumptions; attractive motion graphics alone do not establish production capacity.
Changeover performance needs equally careful measurement. Compare the time from the last accepted unit of one configuration to the first accepted unit of the next. Include fixture replacement, recipe selection, material preparation, and verification. Independent movers can simplify transport changes while workstation adjustments remain the dominant source of downtime.
We assess an intelligent conveyor system against alternatives using the same demand assumptions. Engineering, controls, maintenance skills, spare parts, and commissioning belong beside throughput in that comparison. For stable routes and modest handling requirements, a simpler conveyor or indexed arrangement may remain the more economical choice.
Choose for the Production Program Ahead
The best case for a linear transport system combines meaningful differences between variants with sufficient production demand to justify adaptable motion and scheduling. Forecast changes should be specific enough to influence the layout, tooling strategy, and control scope.
Our transport portfolio at FHS provides options for evaluating those requirements. The deciding evidence is a credible production plan showing how the proposed system handles the difficult mix, recovers from interruptions, and accommodates planned variants at an acceptable cost.
Public Relations Officer
Miss Zeng