Technical Sharing

2026/11/17

How Are Prismatic Battery Cells Made? Manufacturing Process Explained

17
2026/11/

Prismatic lithium-ion battery cells are manufactured under tightly controlled conditions, spanning raw material preparation, electrode fabrication, cell assembly and final testing. Their rectangular metal housings make them suitable for applications such as electric vehicles (EVs) and energy storage systems, but producing reliable cells requires more than simply placing electrodes inside a metal case.

Each manufacturing stage affects the consistency, performance, and quality of the finished cell. Understanding how these processes work also helps manufacturers identify where automation and production equipment can improve manufacturing control. From individual cell production to downstream battery integration, every step must meet specific technical requirements.

图片 1.jpg

What Happens During Electrode Manufacturing?

Electrode manufacturing transforms active materials into coated metal foils that form the foundation of a lithium-ion battery. The anode and cathode are produced separately before entering the cell assembly stage.

Raw Material Mixing

The process begins with preparing the electrode materials. Active material powders are mixed with conductive additives, binders, and solvents to create a uniform slurry.

The cathode and anode use different material formulations. Consistent mixing is important because uneven material distribution can affect coating quality and subsequent electrochemical performance.

Electrode Coating and Drying

The prepared slurry is applied to thin metal current collectors. Typically, aluminum foil serves as the cathode collector, while copper foil serves as the anode collector.

After coating, the electrodes pass through drying equipment to remove solvents. Manufacturers must control coating thickness, surface uniformity, and residual moisture to maintain consistent electrode quality.

Calendaring, Slitting, and Vacuum Drying

The dried electrodes pass through rollers during calendaring. This process compresses the coatings to achieve the required thickness and density.

The coated foils are then slit into narrower widths according to the cell design. Vacuum drying removes remaining moisture before the electrodes enter cell assembly.

Process

Main purpose

Mixing

Create uniform electrode slurry

Coating and drying

Apply active materials to metal foil

Calendaring

Control electrode thickness and density

Slitting

Prepare electrodes for the required cell dimensions

Vacuum drying

Remove residual moisture

According to Fraunhofer ISI's research on lithium-ion battery cell formats, electrode manufacturing is closely connected to cell dimensions and downstream assembly requirements.

How Are Prismatic Battery Cells Assembled?

Prismatic battery cells are assembled by combining prepared electrodes and separators, inserting the resulting assembly into a rigid housing, and filling the cell with electrolyte before sealing.

Electrode Stacking and Separator Integration

The anode and cathode must remain electrically separated while allowing lithium ions to move between them. A porous separator is placed between the electrode layers to provide this function.

Depending on the cell design, manufacturers may use stacked, folded, or wound electrode assemblies. Accurate positioning is essential because misaligned layers can create manufacturing defects and affect cell consistency.

Cell Housing and Terminal Connection

Once the electrode assembly is prepared, its tabs are connected to the terminal structure. The assembly is then inserted into a rectangular metal casing, and the housing is joined to its cover through a controlled welding process.

The dimensions of the electrodes, separator, and housing must match the intended cell format. This is why prismatic cell production requires specialized handling equipment and fixtures.

Electrolyte Filling and Cell Sealing

Electrolyte is introduced into the housing so that it can penetrate the electrode and separator structures. Manufacturers must control filling conditions to support consistent wetting.

After filling and the required wetting period, the cell is sealed to prevent electrolyte leakage and external contamination.

Important assembly considerations include:

- Accurate electrode and separator alignment.
- Reliable terminal connections and housing welds.
- Controlled electrolyte filling and wetting.
- Consistent sealing quality.
Fraunhofer ISI identifies electrode processing, contacting, housing insertion, electrolyte filling, and sealing as key operations in prismatic cell assembly.

How Are Finished Prismatic Cells Tested?

Finished prismatic cells undergo formation, aging, and quality inspection before they are approved for downstream battery integration. These processes help manufacturers evaluate cell behavior and identify potential defects.

Initial Charging and Formation

Formation is the initial charging and discharging process performed after cell assembly. It activates the cell electrochemically and helps establish the solid-electrolyte interphase (SEI), a protective layer that forms on the anode.

Manufacturers use controlled charging conditions, including current, voltage, and temperature, according to the cell chemistry and design.

Aging and Performance Grading

After formation, cells are commonly stored under controlled conditions while their electrical characteristics are monitored.

Manufacturers may evaluate:

- Voltage consistency.

- Discharge capacity.

- Internal resistance.

- Changes in electrical behavior during storage.

These measurements help identify abnormal cells and group qualified products according to specified performance requirements.

Final Quality Inspection

Before release, cells undergo electrical and physical inspections. Testing requirements vary depending on the manufacturer's product specifications and application.

Testing stage

Main objective

Formation

Establish initial electrochemical behavior

Aging

Monitor cell stability over time

Electrical testing

Evaluate capacity, voltage, and resistance

Final inspection

Identify defects and confirm acceptance requirements

The 2023 research paper Optimizing the Cell Finishing Process: An Overview of Steps, Technologies, and Trends, published in the World Electric Vehicle Journal by researchers from RWTH Aachen University, discusses the importance of formation and quality testing in battery cell production.

How Does FHS Support Prismatic Battery Pack Assembly?

Cell manufacturing and battery pack assembly are separate but connected production stages. After individual cells pass inspection, they can be integrated into modules and packs through mechanical assembly, electrical connections, welding, and testing.

As a smart manufacturing and industrial automation solutions provider,  FHS develops customized automation equipment and production lines for industries including EV batteries and energy storage. Its prismatic battery pack assembly solution focuses on the downstream assembly of power battery modules and packs rather than individual cell fabrication.

图片 2.jpgAutomated Module and Pack Assembly Processes

FHS offers a semi‑automated production line supporting a wide range of assembly processes, per its official product documentation.

These include:
- Cell loading, data matrix code (DMC) scanning, and testing.
- Separator bonding and cell stacking.
- Module pre-stacking and end-plate assembly.
- Side-plate cleaning, gluing, and welding.
- Liquid cooling plate installation.
- Module heating and holding.
- Cell connection component installation and busbar welding.
- End-of-line testing and weighing.

These operations help coordinate the transition from individual cells to assembled battery modules.

Flexible Production and Welding Control

Battery manufacturers may need to produce different module models on the same production line. FHS's solution is designed to support product changeovers with minimal manual intervention.

Its automated stations include side-plate gluing, side-seam welding, module heating, and busbar welding. Camera systems and welding galvanometers monitor cell-position variations and compensate for deviations during welding.

The heating and holding process also uses precision heating plates, with the product page specifying temperature errors controlled within ±5°C. Heating data and temperature curves are uploaded to a Manufacturing Execution System (MES) for monitoring.

Integrated Testing and Quality Monitoring

The production line also incorporates post-welding inspection, end-of-line (EOL) testing, On-Off testing, and weighing.

FHS publishes the following performance figures for this particular solution

Parameter

Published result

Cycle time

116 seconds per module

Product quality rate

98%

Equipment fault rate

Below 8%

Heating temperature error

Within ±5°C

These figures describe the specified production line and should not be treated as universal results for every battery manufacturing project.

From Cell Manufacturing to Battery Pack Assembly

Prismatic battery cell manufacturing involves three major stages: electrode production, cell assembly, and cell finishing. Each stage requires careful process control, from maintaining consistent electrode coatings to ensuring accurate assembly, electrolyte filling, and reliable testing.

However, manufacturing individual cells is only one part of the wider battery production process. Once qualified cells are ready, they must be integrated into modules and packs through additional assembly and inspection operations.

For manufacturers planning or upgrading battery production facilities, understanding this distinction is important when selecting automation equipment. With its semi-automated module and pack assembly solution, FHS supports downstream production through cell handling, welding, heating, and integrated testing.


Sources

1. Fraunhofer Institute for Systems and Innovation Research (Fraunhofer ISI). Development Perspectives for Lithium-Ion Battery Cell Formats (2022). (https://www.isi.fraunhofer.de/content/dam/isi/dokumente/cct/2022/Development_perspectives_for_lithium-ion_battery_cell_formats_Fraunhofer_2022.pdf)

2. Fraunhofer Institute for Solar Energy Systems (Fraunhofer ISE). Wet and Dry Electrode Manufacturing and Thin-Film Technology. (https://www.ise.fraunhofer.de/en/business-areas/electrical-energy-storage/production-technology-for-batteries/wet-and-dry-electrode-manufacturing-and-thin-film-technology.html)

3. Kampker et al., RWTH Aachen University. Optimizing the Cell Finishing Process: An Overview of Steps, Technologies, and Trends. World Electric Vehicle Journal, 2023. (https://www.mdpi.com/2032-6653/14/4/96)

4. FENGHESHENG GROUP. Prismatic Battery Pack Assembly Line. (https://www.ksfhs.com/en/contents/70/11.html)

5. FENGHESHENG GROUP. Official Company Website. (https://www.ksfhs.com/en/)

Public Relations Officer